Kia Sorento: Windshield Glass Installtion
|
1. |
With a knife, scrape the old adhesive smooth to a thickness of
about 2mm (0.08 in.) on the bonding surface around the entire windshield
opening flange :
| A. |
Do not scrape down to the painted surface of the body;
damaged paint will interfere with proper bonding.
|
| B. |
Remove the rubber dam and fastereners from the body.
|
| C. |
Mask off surrounding surfaces before painting.
|
|
|
2. |
Clean the bonding surface with a sponge dampened in alcohol. After
cleaning, keep oil, grease and water from getting on the clean surface.
|
|
3. |
Install the windshield upper moulding (A) and fasteners. Do not
allow any gaps.
|
|
4. |
Install the spacer (A) install the windshield glass (B) temporarily
with marking sure to position them on the center, and then place the
alignment mark (C).
|
|
5. |
Remove the windshield.
|
|
6. |
With a sponge, apply a light coat of body primer to the original
adhesive remaining around the windshield opening flange. Let the body
primer dry for at least 10 minutes.
| A. |
Do not apply glass primer to the body, and be careful
not to mix up glass and body primer sponges.
|
| B. |
Never touch the primed surfaces with your hands.
|
| C. |
Mask off the dashboard before painting the flange.
|
|
|
7. |
Apply a light coat of glass primer to the outside of the fasteners.
|
• |
Never touch the primed surface with your hand.
If you do, the adhesive may not bond to the glass properly,
causing a leak after the windshield glass is installed.
|
|
• |
Do not apply body primer to the glass.
|
|
• |
Keep water, dust, and abrasive materials away
from the primer.
|
|
|
|
8. |
Pack adhesive into the cartridge without air pockets to ensure
continuous delivery. Put the cartridge in a caulking gun, and run a
bead of adhesive (A) around the edge of the windshield (B) between the
fastener and moulding as shown. Apply the adhesive within 30 minutes
after applying the glass primer. Make a slightly thicker bead at each
corner.
|
|
9. |
Use suction cups (A) to hold the windshield over the opening,
align it with the alignment marks (B) made in step 15, and set it down
on the adhesive. Lightly push on the windshield until its edges are
fully seated on the adhesive all the way around. Do not open or close
the doors until the adhesive is dry.
|
|
10. |
Scrape or wipe the excess adhesive off with a putty knife or towel.
To remove adhesive from a painted surface or the windshield, wipe with
a soft shop towel dampened with alcohol.
|
|
11. |
Let the adhesive dry for at least one hour, then spray water over
the windshield and check for leaks. Make leaking areas, and let the
windshield dry, then seal with sealant :
| A. |
Let the vehicle stand for at least four hours after windshield
installation. If the vehicle has to be used within the first
four, it must be driven slowly.
|
| B. |
Keep the windshield dry for the first hour after installation.
|
|
|
12. |
Reinstall all remaining removed parts. Install the rearview mirror
after the adhesive has dried thoroughly. Advise the customer not to
do the following things for two the three days :
| A. |
Slam the door with all the windows rolled up.
|
| B. |
Twist the body excessively (such as when going I in and
out of driveways at an angle or driving over rough, uneven roads)
|
|
|
13. |
Install the following items.
| A. |
Windshield glass deicer connector
(Refer to "Windshield Deicer" in BE group)
|
| D. |
Auto defog sensor
(Refer to "Auto Defog Sensor " in HA group)
|
| E. |
LDWS unit
(Refer to "LDWS Unit" in BE group)
|
| F. |
Rain sensor
(Refer to "Rain Sensor" in BE group)
|
| G. |
Inside rear view mirror
|
|
•
Put on gloves to protect your hands.
•
...
•
Put on gloves to protect your hands.
•
...
See also:
Power Mosfet (DATC) Inspection
1.
Measure the resistance between the terminals.
2.
If the measured resistance is not within specification, the blower
resistor must be rep ...
Winter driving
Severe weather conditions in the winter result in greater wear and other problems.
To minimize the problems of winter driving, you should follow these suggestions:
Snowy or icy conditions
To driv ...
Windshield defrosting and defogging
WARNING - Windshield heating
Do not use the or
position during cooling operation
in extremely humid weather. The difference between the temperature of the outside
air and the windshield could ca ...
Windshield Glass Removal
Quarter Fixed Glass Removal