Kia Sorento: Head Lamps Inspection
|
1. |
Check-points upon head lamp failure (HID)
|
(1) |
Check the battery voltage. (Low beam will be on when the
battery voltage above 9V.)
|
|
(2) |
Check the fuse and relay.
|
|
(3) |
Check the polarity of ballast. (If the polarity are changed,
low beam doesn't lighten)
|
|
(4) |
Check the bulb connector securely.
|
|
(5) |
Visually bulb checking (no filament): damaged glass, damaged
for upper parts and lower parts of glass tube.
|
|
(6) |
After (1)~(5), replace the ballast and the ignitor. (ballast
assembly).
|
|
|
2. |
Service procedure and warning (HID)
No.
|
Item
|
Service procedures
|
Warning
|
Remarks
|
1
|
Replacement of lamp assembly
|
|
1. |
Disconnect the power connector from the lamp.
|
|
2. |
Remove and replace the lamp assembly.
|
|
3. |
Connect the power connector.
|
|
|
• |
Disconnect the head lamp power connector to avoid
high voltage.
|
|
|
• |
Other description is the same as the halogen bulbs.
|
|
2
|
Replacement of the Bulb
|
|
1. |
Disconnect the power connector from the lamp.
(head lamp, turn signal, head lamp leveling device)
|
|
2. |
Remove the lamp assembly.
|
|
3. |
Remove the ballast and dust cover.
|
|
4. |
Remove the bulb socket and replace the bulb.
|
|
5. |
Installation is the reverse of removal.
|
|
|
• |
Disconnect the head lamp power connector to avoid
high voltage.
|
|
• |
Be careful not to damage the bulb and use genuine
bulbs only.
|
|
• |
Do not apply excessive force and fit it correctly.
|
|
|
3
|
Replacement of the Ballast (with built-in ignitor)
|
|
1. |
Disconnect the power connector from the lamp.
|
|
2. |
Remove the lamp and then the ballast and the dust
cover.
|
|
3. |
Remove the head lamp leveling device and then
the bulb socket.
|
|
4. |
Connect the bulb socket on the replacement ballast
and install the leveling device.
|
|
5. |
Installation is the reverse of removal.
|
|
|
• |
Disconnect the head lamp power connector to avoid
high voltage.
|
|
|
• |
Replace the ballast only and install the used
lamp.
|
|
• |
Replace the sub assembly except the ballast.
|
|
4
|
Others
|
|
1. |
Power supply should be according to the rated
capacity.
|
|
2. |
Use the rated fuse and wire.
|
|
3. |
Bulb socket shall be free from moisture or dirt.
|
|
4. |
Do not apply the ballast severe shock, water,
or extreme
|
|
|
• |
All parts should be serviced only at specified
service centers.
|
|
|
• |
HID lamp should not be installed on other cars
(Dangerous, fire may occur.)
|
|
|
HID lamp shall not be used on other cars.(Fire may occur.)
Fire may occur when HID lamp initially lights due to the
fact that arc-discharge generates high voltage (max. 30,000V)
and high current (12-13A), and are different from the halogen
lamp specification.
|
|
Characteristic
|
1. |
Durable for vibration as there is no filament.
|
|
2. |
HID lamp had a more long life than halogen lamp.
|
|
3. |
Does not operate if polarity is changed.
|
|
4. |
Operating input voltage : 9-16V
|
1.
Bulb
(1)
Elements
Xenon gas: Xenon gas activates the initial reaction for
rapid illuminating.
Molybdenum ...
Head lamps become very hot during use; do not touch them or any
attaching hardware immediately after they have been turn ...
See also:
Description
The charging system included a battery, an alternator with a built-in
regulator, and the charging indicator light and wire.
The Alternator has eight built-in diodes, each rectifying AC curre ...
Tire pressure monitoring system TPMS
(1) Low tire pressure telltale / TPMS malfunction indicator
Each tire, including the spare (if provided), should be checked monthly when
cold and inflated to the inflation pressure recommended by ...
Specification
HO2S [Bank 1/Sensor 1]
Item
Specification
Heater Resistance (Ω)
2.5 ~ 4.0 [20°C(68°F)]
HO2S [Bank 1/Sensor 2]
A/F Ratio (λ)
...
HID Head Lamp
Head Lamps Removal