Kia Sorento: Special Service Tools
Second Generation XM (2011-2024) / Kia Sorento XM 2011-2024 Service Manual / Automatic Transaxle System / Special Service Tools
| Tools (Number and name) |
Illustration |
Use |
| 09200-3N000 Engine support fixture(Beam) |
|
Removal and installation of the transaxle. Except lower supporter, use beam only with new engine support fixture supporter(SST No.:09200-2S000) |
| 09200-2S000 Supporter |
|
Removal and installation of the transaxle. Use this beam (SST No. : 09200-38001/3N000) with the supporter (SST No. : 09200-2S000) |
| 09200-2W000 Adapter |
|
Removal and installation of the transaxle. Use this beam (SST No. : 09200-38001/3N000) with the adapter (SST No. : 09200-2W000) |
| 09453-3L240 Oil seal installer(2WD) |
|
Installation of transaxle case oil seal. (In case of 2WD vehicle use this tool to both sides when installing oil seal, and 4WD vehicle should use transaxle case side only.) [Using with bar (SST No.:09231-H1100)] |
| 09453-2W100 Oil seal installer(4WD) |
|
Installation of transaxle case oil seal. (In case of 4WD vehicle use this tool to transaxle housing side when installing oil seal.) [Using with bar (SST No.:09231-H1100)] |
| 09231-H1100 Bar |
|
Installation of transaxle case oil seal. [Using with oil seal installer (SST No.:09453-3L241, 09453-2W100)] |
| 09480-A3800 Inhibitor switch guide pin |
|
| ※ Engine support fixture special tool assembly drawing |
| 1. 09200-3N000(Main bar) 2. 09200-3N000(Sub bar) 3. 09200-3N000(Handle) 4. 09200-3N000(Stopper) 5. 09200-3N000(Stopper) 6. 09200-3N000(Knobe) 7. 09200-3N000(Adapter) 8. 09200-2S000(Supporter) 9. 09200-3N000(Hanger) |
10. 09200-3N000(Clip) 11. 09200-3N000(Nut) 12. 09200-3N000(Pin) 13. 09200-2S000(Stopper) 14. 09200-2S000(Spacer) 15. 09200-2S000(Adapter) 16. 09200-2S000(Nut) 17. 09200-2S000(Supporter) 18. 09200-2W000(Adapter) |
Lubricants
Item
Specified lubricant
Quantity
Transaxle fluid
ATF SP-Ⅳ or equivalent
7.8 L
(2.06 U.S gal.,8.24 U.S.qt., 6.86 Imp.qt.)
...
Fault Diagnosis
Features a fail-safe mechanism that provides "limp-home" 4th gear hold
to enable the vehicle to be driven to the owner's home or dealer shop.
Fail-Safe: The TCM provides 4th ge ...
See also:
General Inspection
After or before servicing the EPS system, perform the troubleshooting
and test procedure as follows. Compare the system condition with normal condition
in the table below and if abnormal symp ...
Water pump Components
1. Water pump pulley
2. Water pump
3. Water pump gasket
4. Water pump housing
5. Water pump housing gasket
6. O-ring
7. Water inlet pipe
...
Filter replacement
It must be replaced when necessary, and should not be washed.
You can clean the filter when inspecting the air cleaner element. Clean the filter
by using compressed air.
1. Loosen the air clean ...
Copyright В© www.ksmanual.com 2014-2024