Kia Sorento: Front Hub / Knuckle / Tone Wheel Removal and Installation - Front Axle Assembly - Driveshaft and axle - Kia Sorento XM 2011-2024 Service ManualKia Sorento: Front Hub / Knuckle / Tone Wheel Removal and Installation

Second Generation XM (2011-2024) / Kia Sorento XM 2011-2024 Service Manual / Driveshaft and axle / Front Axle Assembly / Front Hub / Knuckle / Tone Wheel Removal and Installation

1.
Remove the front wheel and tire (A) from front hub .

Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)

  
Be careful not to damage to the hub bolts when removing the front wheel and tire (A).

2.
Remove the brake caliper mounting bolts, and then place the brake caliper assembly (A) with wire.

Tightening torque:
78.4 ~ 98.0N.m (8.0 ~ 10.0kgf.m, 57.8 ~ 72.3lb-ft)

3.
Remove the coking nut (A).

Tightening torque:
240.3~ 269.7N.m (24.5 ~ 27.5kgf.m, 177.2 ~ 198.9lb-ft)

  
•
The front hub coking nut should be replaced with new ones.
•
After installation coking nut (A), stake the coking nut using a chisel and hammer as shown in the illustration below.

4.
Remove the brake hose (A) and wheel speed sensor (B).

Tightening torque:
6.8 ~ 10.8N.m (0.7 ~ 1.1kgf.m, 5.1 ~ 7.9lb-ft)

5.
Remove the tie rod end ball joint (C) from the knuckle.
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).

Tightening torque:
23.5 ~ 33.3N.m (2.4 ~ 3.4kgf.m, 17.4 ~ 24.6lb-ft)

6.
Disconnect the ball joint(A) from knuckle using the special tool (09568-4A000).

7.
Remove the lower arm (A) mounting bolt and nut from the knuckle.

Tightening torque:
98.0 ~ 117.6N.m (10.0 ~ 12.0kgf.m, 72.3 ~ 86.7lb-ft)

8.
Loosen the strut mounting bolts(A) and then remove the hub and knuckle assembly from the strut assembly (B).

Tightening torque:
156.9 ~ 176.5N.m (16.0 ~ 18.0kgf.m, 115.7 ~ 130.1Ib-ft)

9.
Install in the reverse order of removal.
  
•
Use a SST (09581-11000) when installing the brake caliper assembly.
(Refer to Brake System - "Front Disc Brake")
Front Hub / Knuckle / Tone Wheel Components
1. Knuckle 2. Dust cover 3. Hub assembly 4. Brake disc ...

Front Hub / Knuckle / Tone Wheel Disassembly
1. Remove the brake disc (B) from the knuckle assembly (A). Tightening torque: 4.9 ~ 5.9N.m (0.5 ~ 0.6kgf.m, 3.6 ~ 4.3Ib-ft) ...

See also:

Rear Disc Brake Components
1. Guide rod bolt 2. Bleed screw 3. Caliper carrier 4. Caliper body 5. Inner pad shim 6. Brake pad 7. Pad retainer ...

Direct Electro Hydraulic Actuator Coupling Components
1. Coupling assembly 2. Input shaft 3. Pressure sensor 4. Extension wiring 5. Oil hydraulic Motor(Actuator) ...

Rear Door vReplacement
Door Trim Replacement    • When prying with a flat-tipped screwdriver, wrap it with p ...

Copyright © www.ksmanual.com 2014-2024