Kia Optima Manuals

Kia Sorento: Inspection - Keyless Entry And Burglar Alarm - Body Electrical System - Kia Sorento XM 2011-2025 Service ManualKia Sorento: Inspection

Second Generation XM (2011-2025) / Kia Sorento XM 2011-2025 Service Manual / Body Electrical System / Keyless Entry And Burglar Alarm / Inspection

Front Door Lock Actuator
1.
Remove the front door trim.
(Refer to Body - "Front door")
2.
Remove the front door module.
(Refer to Body - "Front door")
3.
Disconnect the connectors from the actuator.
4.
Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.
Rear Door Lock Actuator
1.
Remove the rear door trim.
(Refer to Body - "Rear door")
2.
Remove the rear door module.
(Refer to Body - "Rear door")
3.
Disconnect the connectors from the actuator.
4.
Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.
Tailgate Lock Actuator Inspection
1.
Remove the tailgate trim.
(Refer to Body - "Tailgate")
2.
Disconnect the 4P connector from the actuator.
3.
Check actuator operation by connecting power and ground according to the table. To prevent damage to the actuator, apply battery voltage only momentarily.
Front Door Lock Switch
1.
Remove the front door trim.
(Refer to Body - "Front door")
2.
Remove the front door module.
(Refer to Body - "Front door")
3.
Disconnect the connectors from the actuator.
4.
Check for continuity between the terminals in each switch position when inserting the key into the door according to the table.
Rear Door Lock Switch
1.
Remove the rear door trim.
(Refer to Body - "Rear door")
2.
Remove the rear door module.
(Refer to Body - "Rear door")
3.
Disconnect the connectors from the actuator.
4.
Check for continuity between the terminals in each switch position according to the table.
Tailgate Switch
1.
Remove the tailgate trim.
(Refer to Body - "Tailgate")
2.
Disconnect the 4P connector from the actuator.
3.
Check for continuity between the terminals in each switch position according to the table.
Door Switch
Remove the door switch and check for continuity between the terminals.

Hood Switch
1.
Disconnect the connector (A) and bolt from the hood switch.
2.
Check for continuity between the terminals and ground according to the table.
[2P Connector]

[1P Connector]
Burglar Horn
1.
Remove the burglar horn after removing a bolt and disconnect the 2P connector from the burglar horn.
2.
Test the burglar horn by connecting battery power to the terminal 1 and ground the terminal 2.
3.
The burglar horn should make a sound. If the burglar horn fails to make a sound replace it.
Description
Burglar Alarm State [B/A State] B/A State Description DISARM 1. In "DISARM" state, no vehicle start inhibition. So, whe ...

Transmitter Inspection
1. Check that the red light flickers when the door lock or unlock button is pressed on the transmitter. 2. Remove the battery (A) and check ...

See also:

Component Replacement After Deployment
   Before doing any SRS repairs, use the GDS Pro to check for DTCs. Refer to the Diagnostic Trouble Code list for repairing ...

Power Door Lock Switch Diagnosis With GDS
1. It will be able to diagnose defects of door lock with GDS quickly. GDS can operates actuator forcefully, input/output value monitoring and self diagnosis. ...

Overdrive Clutch Control Solenoid Valve(OD/C_VFS)
Overdrive clutch control solenoid valve(OD/C) is attached to the valve body. This variable force solenoid valve directly controls the hydraulic pressure inside the overdrive clutch. ...

Categories


Copyright © www.ksmanual.com 2014-2025