Kia Sorento: Specification
| Items |
Inner side |
Outer side |
||
| Front driveshaft |
2.4GDI M/T |
Joint type |
LSJ 104 |
UBJ 104 |
| Max. permissible angle |
23° |
50° |
||
| 2.4GDI A/T |
Joint type |
LSJ 100 |
UBJ 100 |
|
| Max. permissible angle |
23° |
50° |
||
| 3.3GDI A/T |
Joint type |
LSJ 104 |
UBJ 104 |
|
| Max. permissible angle |
23° |
50° |
||
| Rear driveshaft |
Joint type |
EDJ 82 |
EBJ 82 |
|
| Max. permissible angle |
|
|
||
| Rear differential |
Oil type |
Hypoid gear oil, MS 517-15 GT (SAE 75W/90, API GL-5, SHELL SPIRAX X) |
||
| Oil capacity (L) |
0.53±0.05 |
|||
| Reduction gear type |
Hypoid gear |
|||
| Reduction gear ratio |
2.533 |
|||
| Final drive gear backlash mm(in.) |
0.07 ~ 0.15 |
|||
| Differential gear backlash mm(in.) |
0 ~ 0.05 |
|||
Tightening torques
| Items |
Nm |
Kgf-m |
lb-ft |
|
| Front |
Wheel nut |
88.3 ~ 107.9 |
9.0 ~ 11.0 |
65.1 ~ 79.6 |
| Driveshaft nut |
240.3 ~ 269.7 |
24.5 ~ 27.5 |
177.2 ~ 198.9 |
|
| Strut assembly lower mounting bolt |
156.9 ~ 176.5 |
16.0 ~ 18.0 |
115.7 ~ 130.1 |
|
| Inner shaft bearing bracket bolt |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.1 ~ 50.6 |
|
| Break caliper mounting bolt |
78.4 ~ 98.0 |
8.0 ~ 10.0 |
57.8 ~ 72.3 |
|
| Wheel speed sensor mounting bolt |
6.9 ~ 10.8 |
0.7 ~ 1.1 |
5.1 ~ 8.0 |
|
| Break disc mounting screw |
4.9 ~ 5.9 |
0.5 ~ 0.6 |
3.6 ~ 4.3 |
|
| Lower arm ball joint mounting bolt |
98.1 ~ 117.7 |
10.0 ~ 12.0 |
72.3 ~ 86.8 |
|
| Tie rod end ball joint mounting nut |
23.5 ~ 33.3 |
2.4 ~ 3.4 |
17.3 ~ 24.5 |
|
| Rear |
Wheel nut |
88.3 ~ 107.9 |
9.0 ~ 11.0 |
65.1 ~ 79.6 |
| Driveshaft castle nut |
240.3 ~ 269.7 |
24.5 ~ 27.5 |
177.2 ~ 198.9 |
|
| Shock absorber upper mounting bolt |
137.3 ~ 156.9 |
10.0 ~ 12.0 |
101.3 ~ 115.7 |
|
| Shock absorber lower mounting nut |
137.2 ~ 156.9 |
14.0 ~ 16.0 |
101.2 ~ 115.7 |
|
| Break caliper mounting bolt |
63.7 ~ 73.5 |
6.5 ~ 7.5 |
47.0 ~ 54.2 |
|
| Wheel speed sensor mounting bolt |
6.9 ~ 10.8 |
0.7 ~ 1.1 |
5.1 ~ 8.0 |
|
| Break disc mounting screw |
4.9 ~ 5.9 |
0.5 ~ 0.6 |
3.6 ~ 4.3 |
|
| Hub assembly mounting bolt |
78.4 ~ 98.0 |
8.0 ~ 10.0 |
57.9 ~ 72.3 |
|
| Upper arm mounting nut (to knuckle) |
2WD : 137.2 ~ 156.9 |
14.0 ~ 16.0 |
101.2 ~ 115.7 |
|
| 4WD : 98.1 ~ 117.7 |
10.0 ~ 12.0 |
72.3 ~ 86.8 |
||
| Lower arm mounting bolt |
137.3 ~ 156.9 |
14.0 ~ 16.0 |
101.3 ~ 115.7 |
|
| Assist arm ball joint mounting nut |
44.1 ~ 53.9 |
4.5 ~ 5.5 |
32.5 ~ 39.8 |
|
| Parking cable mounting nut |
6.9 ~ 10.8 |
0.7 ~ 1.1 |
5.1 ~ 8.0 |
|
| Trailing arm mounting bolt |
44.1 ~ 53.9 |
4.5 ~ 5.5 |
32.5 ~ 39.8 |
|
| Propeller shaft |
Propeller shaft mounting bolt |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
| Propeller shaft center bearing bracket mounting bolt |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
|
| Rear propeller shaft mounting bolt |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
|
| Differential |
Rear differential mounting bolt |
68.6 ~ 88.3 |
7.0 ~ 9.0 |
50.6 ~ 65.1 |
| Differential cover mounting bolt |
68.6 ~ 88.3 |
7.0 ~ 9.0 |
50.6 ~ 65.1 |
|
| Differential gear drain plug |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
|
Lubricants
Items
Lubricants
Quantity (g)
Front driveshaft
LSJ 104
SH06-VX21
240 ~ 255
UBJ 104
RBA
165 ~ 175
LSJ 100
...
See also:
Tires/Wheels
•
Using tires and wheel other than the recommended sizes
could cause unusual handling ...
Heated Oxygen Sensor (HO2S)
Heated Oxygen Sensor (HO2S) consists of zirconium and alumina and is installed
both upstream and downstream of the Manifold Catalytic Converter. The sensor
output voltage varies in accordance ...
Power Door Mirror Switch Installation
Driver Door Mirror Switch
1.
Install the driver door module and connectors.
2.
Install the front door trim.
...
Copyright © www.ksmanual.com 2014-2024