Kia Sorento: Description
Burglar Alarm State [B/A State]
B/A State
|
Description
|
DISARM
|
| 1. |
In "DISARM" state, no vehicle start inhibition. So, when
door, hood, or Tailgate is opened, there is no alarm sound and
flashing.
|
| 2. |
If the battery is disconnected while the state is not
"ARM/ARMWAIT/ALARM/REARM", B/A state is set to "DISARM" state.
|
|
ARMWAIT
|
| 1. |
In "ARMWAIT" state, when timer “30sec." is running, if
this timer reaches “30sec”, state transits to "ARM" state.
|
| 2. |
If the battery is disconnected while the state is "ARMWAIT",
B/A state is set to "ARMWAIT" state and timer "30sec" is restarted.
|
|
※ Remark: On Smart key system, it works the same way with passive lock
B/A State
|
Description
|
AUTO LOCK TIMER 1
|
| 1. |
In "AUTOLOCKTIMER1" state, timer “30sec."is running. If
this timer expired, the auto lock command is generated “Lock
command”.
|
| 2. |
When “Lock command” operated, All Door changed lock and
closed then B/A state changes “AUTOLOCKTIMER1” to “ARMWAIT
|
| 3. |
In "AUTOLOCKTIMER1" state, Security Indicator keeps blinking.
In "AUTOLOCKTIMER1" state, timer “30sec."is running. If this
timer expired, the auto lock command is generated “Lock command”.
When “Lock command” operated, All Door changed lock and closed
then B/A state changes “AUTOLOCKTIMER1” to “ARMWAIT
|
|
※ Remark: On Smart key system, it works the same way with passive unlock
B/A State
|
Description
|
AUTO LOCK TIMER 2
|
| 1. |
In "AUTOLOCKTIMER2" state, when timer “30sec."is running,
if this timer expired, the auto lock command is generated “Lock
command”.
|
| 2. |
All doors are Locked, Hood is closed and Tailgate is closed
when “Lock command” operated, then B/A state changes to“AUTOLOCKTIMER2”
when “Lock Command” generated with Hood open.
|
| 3. |
When “Unlock command” operated on the condition of All
Door closed and Hood open, B/A state changes to “AUTOLOCKTIMER2”.
|
|
※ Remark: On Smart key system, it works the same way with passive unlock
B/A State
|
Description
|
PRE ARM
|
| 1. |
The "PREARM" state is when user try to change to arm but
pre-condition are not satisfied (door open, tailgate open, or
hood open).
|
| 2. |
B/A state changes to “PREARM” when TX Lock command occurs
with any door Open, Hood or Tailgate Open.
|
| 3. |
B/A state changes to “PREARM” when “30sec.” timer expired
in“AUTOLOCKTIMER2”with Hood or Tailgate Open
|
| 4. |
The “PREAMR” state changes to “ARM” when all doors closed,
All doors locked and Hood and Tailgate closed.
|
| 5. |
The “PREAMR” state changes to “DISARM” when Any Door Unlock
|
|
B/A State
|
Description
|
RE ARM
|
| 1. |
In "REARM" state, if the vehicle intrusion is detected,
flashing and sound is restarted, again and state transits to
"ALARM" state.
|
| 2. |
B/A state changes to “REARM” after the timer “27sec.”
expires in “ALARM” state with All doors closed and lock.
|
|
B/A State
|
Description
|
AUTOLOCK TIMER3
|
| 1. |
B/A state changes to “AUTOLockTIMER3”, when TX-Tailgate
command operated.
|
| 2. |
B/A state changes “AUTOLOCKTIMER3” to “ARMWAIT”, when
the “30sec.” timer expires with all doors lock and closed.
|
| 3. |
B/A state changes “AUTOLOCKTIMER3” to “DISARM”, when any
door open.
|
| 4. |
In "AUTOLOCKTIMER3" state, timer “30sec.“ timer is running.
If this timer expired, state transits to "PREARM" state with
Tailgate Open.
|
|
1. Hood switch
2. Burglar horn
3. IPM & RF receiver
4. Key warning switch
5. Front door switch
6. Front door lock actuator & switch
7. Rear door lock actuator ...
Front Door Lock Actuator
1.
Remove the front door trim.
(Refer to Body - "Front door")
2.
Remove the front door module.
...
See also:
User Settings Mode
Description
On this mode, you can change setting of the doors, lamps, and so on.
Door
Auto Door Lock (if equipped)
• Off:
The auto door lock operation will be deactivated.
• Speed: ...
Crankshaft Inspection
1.
Check the crankshaft bearing oil clearance.
(1)
To check main bearing-to-journal oil clearance, remove the main
caps and bearing ...
Direct Electro Hydraulic Actuator Coupling Description
4WD ECU processes signals from various sensors and determines the current
road and driving conditions. The ECU then utilizes this information to implement
precision control over the 4WD coupl ...
Component Location
Inspection